Azek Deck EN Manual de usuario Pagina 4
- Pagina / 16
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Page 4
Expansion and Contraction
AZEK Deck/Rim Joist Covers/Riser will have expansion and contraction with changes in temperature,
unlike wood whose size will uctuate with moisture changes. The expansion and contraction encountered
may result in slight gaps, which might be noticed at the ends of boards or in splice joints. Fastening the
deck boards according to the Installation Guidelines will help minimize expansion and contraction.
• Expansion/contraction is most signicant where extreme temperature change may exist.
• Best practice is to cut and fasten the deck boards as soon after cutting as possible.
• Install the boards together tightly at splices or miters.
• Be sure to fasten ends of boards, splices, or abutments to building or structure securely into framing
using 2 screws. Position the screws at or within 1/2” of each board end or joint and 3/4” from side of
deck plank.
• Provide a 1/8” to 1/4” side to side gap between deck boards.
• In areas with obstructed airow such as roofs and on-grade applications, a minimum of 1-1/2” sleeper
system supported by and connected to the substructure over which the deck is built is required.
• All deck frames and substructure should be securely attached to ground footings or building
structure. No oating substructures should be used (from preparation section AZEK).
• For best results, stagger splices and miters across deck surface so that all splices and miters do not
break on the same joist or beam.
• To further minimize expansion and contraction, proper ventilation and air ow should be considered.
• Some area building codes may require double joisting when joining boards end to end. Double
joists are always required at butt joints when using CONCEALoc. Always check with your local code
authority for specic requirements before installation.
3/4”
1/2”
Working with AZEK Deck Boards
- AZEK Deck 1
- Install Guide 1
- Installation Guidelines 2
- Working with AZEK Deck Boards 3
- INSTALL THE FIRST PLANK 6
- Tools Needed 6
- POSITION CONCEALoc FASTENERS 7
- INSTALL CONCEALoc FASTENERS 7
- Offset 1/4” 8
- From Center 8
- HOW TO INSTALL ON DIAGONAL 9
- HOW TO REPLACE A PLANK 9
- COLLECTION SOLID DECK BOARDS 10
- Stair Code Compliance 11
- Trimming an AZEK 12
- Care and Cleaning 13
- AZEK Building Products, Inc 16
Relacionado con productos y manuales para Para Casa Azek Deck EN
Para Casa Azek Deck FR Manual de usuario
(4 paginas)
(4 paginas)
Para Casa Azek InDeck Manual de usuario
(4 paginas)
(4 paginas)
Para Casa Azek Bench Planter Manual de usuario
(10 paginas)
(10 paginas)
Para Casa Azek Porch ES Manual de usuario
(2 paginas)
(2 paginas)
Para Casa Azek Porch FR Manual de usuario
(2 paginas)
(2 paginas)
Para Casa Azek Porch EN Manual de usuario
(8 paginas)
(8 paginas)
Para Casa Azek Rail Manual de usuario
(12 paginas)
(12 paginas)
Para Casa Azek Rail Manual de usuario
(16 paginas)
(16 paginas)
Para Casa Azek Rail Manual de usuario
(40 paginas)
(40 paginas)
Para Casa Azek Rail Manual de usuario
(4 paginas)
(4 paginas)
Para Casa Azek TT-AZ Manual de usuario
(2 paginas)
(2 paginas)
Para Casa Azek Rail Manual de usuario
(20 paginas)
(20 paginas)
Para Casa Azek Stair Rail Manual de usuario
(4 paginas)
(4 paginas)
Para Casa Azek Straight Rail Manual de usuario
(4 paginas)
(4 paginas)
Para Casa Azek 22_5 Degree Manual de usuario
(2 paginas)
(2 paginas)
Para Casa Azek Post Sleeve Manual de usuario
(1 paginas)
(1 paginas)
Para Casa Azek SMB Manual de usuario
(1 paginas)
(1 paginas)
Para Casa Azek Tallboy SMB Manual de usuario
(1 paginas)
(1 paginas)
Para Casa Azek Glass Panel Manual de usuario
(1 paginas)
(1 paginas)
Vollrath Induction Undercounter Warming Kits manuály
Uživatelské manuály a uživatelské příručky pro Hardware Vollrath Induction Undercounter Warming Kits.
Poskytujeme 1 manuály pdf Vollrath Induction Undercounter Warming Kits ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentarios a estos manuales